Primary and secondary synchronization signals (PSS & SSS) in LTE


Cell synchronization is the very first step when UE wants to camp on any cell. From this, UE acquires physical cell id (PCI), time slot and frame synchronization, which will enable UE to read system information blocks from a particular network.

UE will tune it radio turn by turning to different frequency channels depending upon which bands it is 
supporting. Assuming that it is currently tuned to a specific band / channel, UE first finds the primary 
synchronization signal (PSS) which is located in the last OFDM symbol of first time slot of the first subframe (subframe 0) of radio frame as shown in figure (green squares). This enables UE to be synchronized on subframe level. The PSS is repeated in subframe 5 which means UE is synchronized on 5ms basis since each subframe is 1ms. From PSS, UE is also able to obtain physical layer identity (0 to 2).

In the next step UE finds the secondary synchronization signal (SSS). SSS symbols are also located in the same subframe of PSS but in the symbol before PSS as shown in the figure(yellow squares). From SSS, UE is able to obtain physical layer cell identity group number (0 to 167).

Using physical layer identity and cell identity group number, UE knows the PCI for this cell now. In LTE 504 physical layer cell identities (PCI) are allowed and are divided into unique 168 cell layer identity groups where each group consist of three physical layer identity. As mentioned earlier, UE detects physical layer identity from PSS and physical layer cell identity group from SSS. Assuming physical layer identity = 1 and cell identity group=2 then the PCI for given cell is

PCI = 3*(Physical layer cell identity group)+ physical layer identity = 3*2+1 = 7

Once UE knows the PCI for a given cell, it also knows the location of cell Reference signals as shown in figure (red and black squares). Reference signals are used in channel estimation, cell selection / reselection and handover procedures. 



LTE Resource Grid (Source: http://paul.wad.homepage.dk/LTE/lte_resource_grid.html)

After cell synchronization procedure, UE will proceed to read Master information and other System information blocks
Please see below sections
Master information block (MIB)
System information block 1 (SIB1)
System information block 2 (SIB2)


84 comments:

  1. Excellent job here. Thanks very much. I finally have come to understand this complex procedure intuitively.

    ReplyDelete
  2. "From PSS, UE is able to obtain physical layer cell identity group number (0 to 167)."

    I think you mean "From SSS".

    ReplyDelete
    Replies
    1. Hi thanks for pointing out this mistake.

      Delete
    2. Hi ,
      Can you please explain on which channel PSS & SSS transmitted???

      Delete
    3. PSS and SSS are signals transmitted in PDSCH.

      Delete
  3. Hi, please can you help me
    I don't understand how can we know from the PCI the RS location?
    thank you

    ReplyDelete
    Replies
    1. Hi,
      The location of RS is fixed in time domain but changing in frequency domain. There are only six different locations or shifts possible for RS allocations. In other words for 84 PCIs there is one fixed location (84*6=504). So once the UE knows PCI, it also knows which one of the six possible shift/location is used for RS allocation
      Use this resource grid generator http://paul.wad.homepage.dk/LTE/lte_resource_grid.html and you will understand what i am saying. As you increase the PCI value from 0 and above, the RS location is repeating in cycle after 6 shifts

      Delete
    2. ok!!! Thank you very much! we get it!

      Delete
    3. Hi can you please explain RS allocation is affected by MIMO or diversity scenarios

      Delete
  4. Hi,

    I am using VSA for a LTE signal demodulation. knowing the PCI,I have already set the RS frequency shift, but still the demodulation is not correct.
    Is there any other parameters to set apart from the center frequency, the bandwith and the RS location...?
    If any ideas, please let me know

    Thanks,

    ReplyDelete
    Replies
    1. Hi Zineb,
      I dont have much experience on VSA tools, sorry for that

      Probably you can ask question here
      http://www.home.agilent.com/owc_discussions/forum.jspa?forumID=87

      Br,
      Adnan

      Delete
  5. Hi,

    I wonder how the UE keep the synchronization after achieving initial synchronization. I mean, whether it constantly monitor the PSS and SSS or it keep synchronization in another way. What is the difference in IDLE and CONNECTED mode in this regard?

    Thank you in advance

    ReplyDelete
    Replies
    1. Hi,
      My understanding is as below
      * PSS and SSS are for initial synchronization only (idle to connected ) or every time RACH is required
      * During call, reference signals are used for synchronization
      * In idle mode, UE monitors PA-RNTI on every paging cycle

      Delete
    2. Thank you for your response,
      Do you know the 3GPP reference, where it is described?

      Delete
  6. Hello!
    Sorry for offtopic:
    Сan be packaged in one RB for the user data and signaling information?

    ReplyDelete
  7. Hi.. Yes user data (DRB)and signalling information (SRB) can be sent in one resource block ..

    ReplyDelete
  8. Its mentioned here that PSS is repeated in sub-frame 5.
    But, I have read that PSS is sent in sub-frame 0 and sub-frame 9.
    Can any1 please explain.

    ReplyDelete
    Replies
    1. primary synchronization signal is transmitted twice per radio frame, so it is repeated in subframe 5 to provide 5m synchronization.. what is your source of information ?

      Delete
  9. Hi Adnan,

    In your previous posts you explained:-
    In other words for 84 PCIs there is one fixed location (84*6=504).

    Does this 84 number is derived from 12 (sub carriers) * 7 Symbols = 84 [Resource grid] from 1.4 Mhz BW ?
    or is this Resource grid block [12 *7] is constant for all BW's in LTE ?

    Please explain and correct me if y understanding is wrong

    ReplyDelete
    Replies
    1. Hi Pavan,
      This number 84 is not derived from 12*7 .. you are getting it wrong.. what i meant is that if we change PCI value by one then there is one shift in RS in frequency domain. but after every 6 shifts all RS comes to same location. so if 504/6 = 84...there fore we can say that 84 PCIs share same RS location

      Delete
  10. This comment has been removed by the author.

    ReplyDelete
  11. Hi Adnan,

    Thanks for the amazing blog. I need a detailed description (on bit or byte level) of SIB1. Please give me some direct reference.
    Best regards,
    Nidal

    ReplyDelete
  12. hi,
    i have a query about the part just below and above pss/sss which is in black.
    1) it says it is unused by a specific antenna port or undefined for all antenna port , what does this mean exaclty??

    2) also if one were to map PRS (positioning reference signal), will it be mapped in this black spots ??? i mean it is exactly not pss/sss, and in specs it says that PRS will not be mapped to the resource elements reserved for PSS/SSS and PBCH???

    ReplyDelete
  13. Adnan hi,
    Long time no see after Helsinki (=
    I have a question about PCI planning. Is it technically possible to assign different SSS for the cells on the same enodeb (at same earfcn)...? Thus the PCIs will be non-consecutive..!

    ReplyDelete
    Replies
    1. Hi Utku,
      Good to hear from you... EARFCN basically defines the bandwidth allocated to a given cell.. while PCI is used to identify a cell and is used in synchronization process.. so it is possible for two adjacent cells to have same EARFCN but PCI has to be different of-course else there will be synchronization issue. If the PCI is different then SSS is also different for these two cell...

      Example

      Lets assume we have eNodeB with two cells. Following configuration is possible

      Cell1 Earfcn: 2600
      Cell 1 PCI : 10

      Cell2 Earfcn: 2600
      Cell2 PCI: 11

      PCI can be any value as long as they are not same for adjacent cells

      Delete
    2. adjacent or neighbor cells *

      Delete
  14. might be this is a very silly question can you please explain how UE will know that this is the bandwidth where i will look for PSS and SSS , since till that point MIB has not been broadcast.
    And also which one is 0 and 10th slot, 7th symbol as there is no information of all those things.

    ReplyDelete
    Replies
    1. by either a preferred frequency list or by scanning a 100 KHs until it gets a correlation hit with the PSS

      Delete
  15. Hi why SSS comes before PSS any specific reason

    ReplyDelete
  16. This comment has been removed by the author.

    ReplyDelete
  17. Hi Adnan,

    Since SSS uses only one OFDM symbol(#5 in # 0Subframe & #5 in #5 Subframe) using QPSK. So, it can only represent a 2bit information. But there could be 168 possible Pseudo Random sequences of SSS.
    Then how UE gets the information of one of the 168 possible combinations of SSS?

    ReplyDelete
    Replies
    1. How does UE know to such slot and symbol it has to camp on to perform synchronization, thx!

      Delete
    2. The UE initially has no timing info by decoding successfully the PSS it then achieves slot and symbol sync, probably why PSS is at the end of the slot in FDD. By working out which of the 168 sequences in use on SSS the channel is decoded,

      Delete
  18. Hi Adnan,
    Why PSS is positioned after SSS if PSS needs to be decoded first?

    ReplyDelete
  19. UE get frequency from PSS, yes or no and How?

    ReplyDelete
  20. Hi adnan,
    UE get frequency from PSS yes or no and How?
    Thanks

    ReplyDelete
    Replies
    1. No UE must retune and step at 100 KHz until it gets a correlation hit with the PSS, (or goes to last known freq.... typical 3pp UE behavior).
      Knowing the EARFCN is only useful in FDD for the UE to calculate the UL freq.....it already knows the Dl freq.....

      Delete
  21. PSS & SSS are transmitted through which channel???

    ReplyDelete
  22. This is great information about Primary and secondary synchronization signals. I really love it. Thanks for Sharing with us.

    Regard - Blog Tutorial Supporter

    ReplyDelete
  23. I have a question regarding the PSS and SSS. IF PSS and SSS are transmitted on all the 4 antenna ports, then how will UE decode the PSS and SSS.indentify which antenna RS is present where in 4x4 MIMO

    ReplyDelete
  24. Thank you. Very clear..for long time i did not get the clarity. now got it

    ReplyDelete
  25. Complexity has been simplified in this article ...Thank You very much.

    ReplyDelete
  26. Could be a basic question. How could the PSS and SSS could be indentified without knowing the bandwidth information. As MIB is decoded after frame synchronization and cell identification?

    ReplyDelete
  27. Could you please let me know the way to calculate the Sync Signals (PSS&SSS) Power for a 40W, LTE 2100 MHz Network.

    ReplyDelete
  28. Hi there! Nice post! Please tell us when I will see a follow up!
    Buying Drugs Without Prescription

    ReplyDelete
  29. The job of the peruser in thesis composing will differ contingent upon the sort of issue territories that the individual in question will be altering. The significant motivation behind editing is to make the last form of the paper right
    Right Way of Formatting and Styling of Dissertation:

    ReplyDelete
  30. Can I just say what a relief to find someone who actually knows what theyre talking about on the internet. You definitely know how to bring an issue to light and make it important. More people need to read this and understand this side of the story. I cant believe youre not more popular because you definitely have the gift.

    Club House
    Casinobet.mee.nu

    ReplyDelete
  31. Nice post. I learn something more challenging on different blogs everyday. It will always be stimulating to read content from other writers and practice a little something from their store. I’d prefer to use some with the content on my blog whether you don’t mind. Natually I’ll give you a link on your web blog. Thanks for sharing.

    Community.cbr.com
    Information

    ReplyDelete
  32. I’d have to check with you here. Which is not something I usually do! I enjoy reading a post that will make people think. Also, thanks for allowing me to comment!

    Click Here
    Visit Web

    ReplyDelete
  33. You know your projects stand out of the herd. There is something special about them. It seems to me all of them are really brilliant! buy 50 likes instagram

    ReplyDelete
  34. An impressive share, I just given this onto a colleague who was doing a little analysis on this. And he in fact bought me breakfast because I found it for him.. smile. So let me reword that: Thnx for the treat! But yeah Thnkx for spending the time to discuss this, I feel strongly about it and love reading more on this topic. If possible, as you become expertise, would you mind updating your blog with more details? It is highly helpful for me. Big thumb up for this blog post!

    Steepster.com
    Information
    Click Here

    ReplyDelete
  35. Why sss is different in one subframe and pss is same?

    ReplyDelete
  36. Oh my goodness! an amazing article dude. Thank you However I am experiencing issue with ur rss. Don’t know why Unable to subscribe to it. Is there anyone getting identical rss problem? Anyone who knows kindly respond. Thnkx

    Coub.com
    Information
    Click Here

    ReplyDelete
  37. There are some interesting points in time in this article but I don’t know if I see all of them center to heart. There is some validity but I will take hold opinion until I look into it further. Good article, thanks and we want more! Added to FeedBurner as well

    Artmight.com
    Information
    Click Here
    Visit Web

    ReplyDelete
  38. Can I just say what a relief to find someone who actually knows what theyre talking about on the internet. You definitely know how to bring an issue to light and make it important. More people need to read this and understand this side of the story. I cant believe youre not more popular because you definitely have the gift.

    Mmix.com
    Information
    Click Here

    ReplyDelete
  39. Today, I was just browsing along and came upon your blog. Just wanted to say good blog and this article helped me a lot, due to which I have found exactly I was looking. lage land rotterdam

    ReplyDelete
  40. There are certainly a lot of details like that to take into consideration. That is a great point to bring up. I offer the thoughts above as general inspiration but clearly there are questions like the one you bring up where the most important thing will be working in honest good faith. I don?t know if best practices have emerged around things like that, but I am sure that your job is clearly identified as a fair game. Both boys and girls feel the impact of just a moment’s pleasure, for the rest of their lives.

    Visit Web
    Diggerslist.com
    Information

    ReplyDelete
  41. Well, I have got the best information from here the site is fully stuffed with the knowledgeable information.
    find out here

    ReplyDelete
  42. There are certainly a lot of details like that to take into consideration. That is a great point to bring up. I offer the thoughts above as general inspiration but clearly there are questions like the one you bring up where the most important thing will be working in honest good faith. I don?t know if best practices have emerged around things like that, but I am sure that your job is clearly identified as a fair game. Both boys and girls feel the impact of just a moment’s pleasure, for the rest of their lives.

    Website
    Shutterfly.com

    ReplyDelete
  43. Nice post. I learn something more challenging on different blogs everyday. It will always be stimulating to read content from other writers and practice a little something from their store. I’d prefer to use some with the content on my blog whether you don’t mind. Natually I’ll give you a link on your web blog. Thanks for sharing.

    Iamerinelizabeth.com
    Information
    Click Here

    ReplyDelete
  44. You made some decent points there. I looked on the internet for the issue and found most individuals will go along with with your website.

    Nable.bytowngroup.com
    Information
    Click Here
    Visit Web

    ReplyDelete
  45. I’d have to check with you here. Which is not something I usually do! I enjoy reading a post that will make people think. Also, thanks for allowing me to comment!

    Pinclone.net
    Information
    Click Here
    Visit Web

    ReplyDelete
  46. Do you need Quick Loan to settle your bills and startup
    business? contact us now with your details to get a good
    Loan at a low rate of 2% per Annual
    Do you need Personal Finance?
    Business Cash Finance?
    Unsecured Finance
    Fast and Simple Finance?
    Quick Application Process?
    Finance. Services Rendered include,
    *Debt Consolidation Finance
    *Business Finance Services
    *Personal Finance services Help
    contact us for more information on how to get started:
    (Whats App) number:+919394133968
    please contact email id : patialalegitimate515@gmail.com
    Mr Sorina Jeffery

    ReplyDelete
  47. I discovered your blog site on google and check a few of your early posts. Continue to keep up the very good operate. I just additional up your RSS feed to my MSN News Reader. Seeking forward to reading more from you later on!…

    Diamondsquad.tv
    Information
    Click Here
    Visit Web

    ReplyDelete
  48. I am often to blogging and i really appreciate your content. The article has really peaks my interest. I am going to bookmark your site and keep checking for new information.

    Profile.ameba.jp
    Information
    Click Here
    Visit Web

    ReplyDelete
  49. I haven’t any word to appreciate this post.....Really i am impressed from this post....the person who create this post it was a great human..thanks for shared this with us.
    shiny buds uk

    ReplyDelete
  50. Hello! I just would like to give a huge thumbs up for the great info you have here on this post. I will be coming back to your blog for more soon.

    Ddrfreak.com
    Information
    Click Here
    Visit Web

    ReplyDelete
  51. I discovered your blog site on google and check a few of your early posts. Continue to keep up the very good operate. I just additional up your RSS feed to my MSN News Reader. Seeking forward to reading more from you later on!…

    Amarmp.com
    Information
    Click Here
    Visit Web

    ReplyDelete
  52. I am often to blogging and i really appreciate your content. The article has really peaks my interest. I am going to bookmark your site and keep checking for new information.

    Calis.delfi.lv
    Information
    Click Here
    Visit Web

    ReplyDelete
  53. Spot on with this write-up, I truly think this website needs much more consideration. I’ll probably be again to read much more, thanks for that info.

    Pcmasters.de
    Information
    Click Here
    Visit Web

    ReplyDelete
  54. It was hard to get an updated form out here and be updated here.
    Independent Girls Service in Delhi

    ReplyDelete
  55. You explained it very well and very informative information. Pool Screen Installation Port Charlotte, FL

    ReplyDelete
  56. I have just forwarded this impressive share to a coworker who was doing some research on it. He even bought me breakfast as a result of the fact that I located it for him. I will say it again: Thanks for the treat! But anyway, I appreciate you taking the time to talk about this since I have strong opinions about it and would like reading more about it. Would you mind adding more details to your blog All about Wired and Wireless Technology as you gain more knowledge? It is quite beneficial to me. Definitely recommend this article post. Sonia Pandey

    ReplyDelete
  57. The best herpes remedy online…

    Thank you D Robinson buckler for saving my life,

    I am cured from herpes

    His result is 100% guarantee.

    He can also restore broken

    Relationship/marriage with spiritual prayer

    He brought my ex lover back

    My ex-lover loves me unconditionally

    He can't do without me right now

    Robinsonbuckler11 ( gmail. com )

    Google about Robinson buckler11 to see more reviews..............................................

    ReplyDelete